How to Fix a Leaking Shower Faucet

Fixing a leaking shower faucet is not a difficult. You will want to make sure that if you have a leaky shower faucet, you fix it right away because you are wasting money on your water bill and you could potentially be damaging the surrounding areas in your bathroom. If you are a beginner, here are a few tools and materials that you will need along with some quick steps to help guide you through the process with ease.

Tools and Materials Needed

  • Wrench
  • Screw driver
  • Caulk
  • Caulking gun
  • Washer
  • Towel
  • Bucket
  • Rubber gloves
  • Damp sponge

Step 1 - Shut Off Water

Begin by shutting the water off. You can either shut it off from the area itself using a nearby valve, or you can shut the main water line to the house off completely. Once the water is off, be sure to turn on the faucet in the shower and drain out any of the water that was sitting in the pipes backed up. Allow a few minutes for them to drain completely and use a towel to wipe up any mess.


Step 2 - Remove Hardware

Remove the shower knobs first, They can usually be removed by hand, but if not, use a screw driver to take them off carefully. Then, remove both the water guard as well as the nut. Now, you will need to remove the washer from the faucet. Unscrew the stem, you will need to turn it in a counter clockwise direction. You will find the washer on the end of the stem, take it off and discard.

Step 3 - Install Hardware

Now, clean the area off and replace it with a new washer. Screw the stem back on in a clockwise direction. Attach the nut and water guard back into place and then use your hand and a screw driver to replace the shower knobs completely.

Step 4 - Caulk the Area

Once everything is back into place, you will want to make sure that you caulk the area to avoid any future problems. Place the caulk tube into the caulking gun and make sure to open it all of the way. You may need to make a small cut at the end. Then apply a smooth bead of caulk around the faucet. Use a bucket of water nearby to dampen and rinse off a sponge, as you will not want to turn on the water yet in the shower. Use the sponge to carefully wipe off any of the excess caulk. Allow the caulk to dry completely for 48 hours before you turn the water on or use the shower.

Once it is dry, turn the water supply back on and check to make sure nothing is leaking or dripping now. Typically a broken or old washer is the culprit or even just a loose fixture. Now that you have fixed these aspects, the faucet should be in working order.

Read more:
Tankless Water Heaters Can Generate Savings
The Basics of Sump Pumps
Checklist: Hire a Plumber
Why Does My Faucet Make a Loud Noise?
Is It Time to Replace My Water Heater?
Low Water Pressure
What Can I Do About a Sump Pump Odor?
Six-Must Have Drain Cleaning Tools
Prevent Expensive Damage - Five Ways to Detect Leaks
Tips on Cleaning Out Your Jetted Bathtub
Locating Your Water Shutoff Valve
How to Remove Mineral Deposits in a Flow Control Valve
How to Install a Clean-Out Plug in a Drain
How to Use Plumber Putty on Bathroom Sinks
Unclog Your Toilets - How to Use a Toilet Snake
Learn the Basics of Sewer Line Repair
How to Prepare for Sump Pump Installation
Stop Clogs - How to Prevent Blocked Drains
Sewer Problems - Finding and Fixing Leaks
Garbage Disposal Safety - Five Best Practices
Lean About What makes up Your Garbage Disposal
Fixing a Kitchen Spay Hose
How to Repair Common Toilet Problems - General Toilet Help
How to Fix a Leaky Tap
Three Garbage Disposal Cleaning Tips
Four Ways to Unclog That Stoppoed Up Sink